Прирачник Indesit IN2IFD14CN6 Машина за миење садови

Прирачник

8

TROUBLESHOOTING

PROBLEMS POSSIBLE CAUSES SOLUTIONS

Salt indicator

is lit

Salt reservoir is empty. (After rell the salt indi-

cator may remain lit for several wash cycles).

Rell reservoir with salt (for more information - see page 2).

Adjust water hardness - see table, page 2.

Rinse aid

indicator is lit

Rinse aid dispenser is empty. (After rell the rinse

aid indicator may remain lit for several wash cycles).

Rell dispenser with rinse aid (for more information - see page 2).

The dishwasher

won’t start or

does not respond

to commands.

The appliance has not been plugged in properly.

Insert the plug into the socket.

Power outage.

For safety reasons, dishwasher will not re-start automatically when power

returns. Open dishwasher door, press START/Pause button and close the

door within 4 seconds.

The dishwasher door is not closed. Vigorously push the door until you hear the “click”.

Cycle is interupted by door opening for more

than 4 seconds.

Press START/Pause and close the door within 4 seconds.

It does not respond to commands.

Display shows: 9 or 12 and On/O LED is

blinking rapidly

Switch o the appliance by pressing the ON/OFF button, switch it back

on after approximately one minute and restart the program. If problem

persists, unplug the appliance for 1 minute, then plug it back in.

The dishwasher

won’t drain.

Display shows:

3 and On/O LED

is blinking rapidly

The wash cycle has not nished yet. Wait until the wash cycle nishes.

The drain hose is bent. Check that the drain hose is not bent (see INSTALATION INSTRUCTION).

The sink drain pipe is blocked. Clean the sink drain pipe.

The lter is clogged up with food residues. Clean the lter (see CLEANING THE FILTER ASSEMBLY).

The dishwasher

makes excessive

noise.

The dishes are rattling against each Position the crockery correctly (see LOADING THE RACKS).

An excessive amount of foam has been pro-

duced.

The detergent has not been measured out correctly or it is not suitable

for use in dishwashers (see FILLING THE DETERGENT DISPENSER). Restart

the current cycle by switching OFF the dishwasher, then switch it on

again, select a new program, press START/Pause and close the door with-

in 4 seconds. Please do not add any detergent.

The dishes are

not clean.

The crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).

The spray arms cannot rotate freely, being

hindered by the dishes.

Arrange the crockery correctly (see LOADING THE RACKS).

The wash cycle is too gentle. Select an appropriate wash cycle (see PROGRAMS TABLE).

An excessive amount of foam has been produced.

The detergent has not been measured out correctly or it is not suitable for

use in dishwashers (see FILLING THE DETERGENT DISPENSER).

The cap on the rinse aid compartment has not

been shut correctly.

Make sure the cap of the rinse aid dispenser is closed.

The lter is soiled or clogged. Clean the lter assembly (see CARE AND MAINTENANCE).

There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).

The dishwasher

does not ll the

water.

Display shows: H,

6 and On/O LED

is blinking rapidly

No water in the water supply or the tap is closed.

Make sure there is water in the water supply or the tap running.

The inlet hose is bent.

Make sure the inlet hose is not bent (see INSTALLATION) reprogram the

dishwasher and reboot.

The sieve in the water inlet hose is clogged; it is

necessary to clean it

After having carried out the verication and cleaning, turn o and turn on

the dishwasher and restart a new program.

Dishwasher

nishes the cycle

prematurely.

Display shows: 15

and On/O LED is

blinking

rapidly

Drain hose positioned too low or siphoning

into home sewage system.

Check if end of drain hose is placed at correct height (see INSTALLATION).

Check for siphoning into home sewage system, install air admittance

valve if necessary.

Air in water supply. Check water supply for leaks or other issues letting air inside.

Detergent leaks.

Depends on the liquid detergent used and

can be emphasized in case of delay option is

activated.

Small leaks will not cause machine malfunction and can be avoided by

changing liquid detergent type or using tablets.

In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.

For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.



Policies, standard documentation, ordering of spare parts and additional product information can be found by:

• Using QR code on your product.

• Visiting our website docs.indesit.eu and parts-selfservice.europeanappliances.com

• Alternatively, contact our After-sales Service (See phone number in the warranty booklet).

When contacting our After-sales Service, please state the codes provided on your product’s identication plate.

The model information can be retrieved using the QR-Code reported in the energy label.

The label also includes the model identier that can be used to consult the portal of the registry

at https://eprel.ec.europa.eu.

IEC 436

:

Оцена

Повеќе за овој прирачник

Разбираме дека е практично да имате печатен прирачник за Indesit IN2IFD14CN6 Машина за миење садови. Секогаш можете да го преземете прирачникот од нашата интернет-страница и да го отпечатите сами. Ако сакате да го имате оригиналниот прирачник, ви препорачуваме да контактирате со Indesit. Тие можеби ќе можат да ви дадат оригинален прирачник. Барате прирачник за вашите Indesit IN2IFD14CN6 Машина за миење садови на различен јазик? Изберете го претпочитаниот јазик на нашата интернет-страница и пребарајте го бројот на модел за да видите дали го имаме.

Спецификации

Сите прирачници за Indesit Машини за перење садови
Повеќе прирачници за Машини за перење садови