Прирачник Indesit IN2IFD14CN6 Машина за миење садови

Прирачник

EN

7

CLEANING THE FILTER ASSEMBLY

Regularly clean the lter assembly so that the lters do not clog and

that the waste water ows away correctly.

Using dishwasher with clogged lters or foreign objects inside ltration

system or sprayarms may cause unit malfunction resulting in lose of

performance, noisy work or higher resources usage.

The lter assembly consists of three lters which remove food residues

from the washing water and then recirculate the water.

The dishwasher must not be used without lters or if the lter is

loose.

At least once per month or after each 30 cycles, check the lter assem-

bly and if necessary clean it thoroughly under running water, using a

non-metallic brush and following the instructions below:

1. Turn the cylindrical lter A in an anti-clockwise direction and pull it

out (Fig 1).

2. Remove the cup lter B by exerting a slight pressure on the side

aps (Fig 2).

3. Slide out the stainless-steel plate lter C (Fig 3).

4. In case you nd foreign objects (such as broken glass, porcelain,

bones, fruit seeds etc.) please remove them carefully.

5. Inspect the trap and remove any food residues. NEVER REMOVE the

wash-cycle pump protection (black detail) (Fig 4).

After cleaning the lters, re-place the lter assembly and x it in posi-

tion correctly; this is essential for maintaining the ecient operation of

the dishwasher.

CLEANING THE WATER INLET HOSE

If the water hoses are new or have not been used for an extend-

ed period of time, let the water run to make sure it is clear and free

of impurities before performing the necessary connections. If this

precaution is not taken, the water inlet could become blocked and

damage the dishwasher.

CLEANING THE SPRAY ARMS

On occasions, food residue may become encrusted onto the spray arms

and block the holes used to spray the water. It is therefore recommend-

ed that you check the arms from time to time and clean them with

asmall non-metallic brush.

To remove the upper spray arm, turn the plastic locking ring in a clock-

wise direction. The upper spray arm should be replaced so that the side

with the greater number of holes is facing upwards.

The lower spray arm may be removed by pulling it upwards.

WATER SOFTENING SYSTEM

Water softener automatically reduces water hardness, consequently

preventing scale buildup on heater, contributing also to better cleaning

eciency.

This system regenerates itself with salt, therefore it is required to

rell salt container when empty.

Frequency of regeneration depends on water hardness level setting

- regeneration takes place once per 5 Eco cycles with water hardness

level set to 3.

Regeneration process starts in nal rinse and nishes in drying phase,

before cycle ends.

• Single regeneration consumes: ~3.5L of water;

• Takes up to 5 additional minutes for the cycle;

• Consumes below 0.005kWh of energy.

CARE AND MAINTENANCE

21

43

A

C

A

B

Оцена

Повеќе за овој прирачник

Разбираме дека е практично да имате печатен прирачник за Indesit IN2IFD14CN6 Машина за миење садови. Секогаш можете да го преземете прирачникот од нашата интернет-страница и да го отпечатите сами. Ако сакате да го имате оригиналниот прирачник, ви препорачуваме да контактирате со Indesit. Тие можеби ќе можат да ви дадат оригинален прирачник. Барате прирачник за вашите Indesit IN2IFD14CN6 Машина за миење садови на различен јазик? Изберете го претпочитаниот јазик на нашата интернет-страница и пребарајте го бројот на модел за да видите дали го имаме.

Спецификации

Сите прирачници за Indesit Машини за перење садови
Повеќе прирачници за Машини за перење садови