
6
!
holes; replace it immediately
• Mounting clips w
- align the hole in one of the two clips M with the
threaded hole on the back of the vacuum.
- insert the screws and securely tighten the screw with a
Phillips head screwdriver (not included).
- repeat this steps with the other clip.
• Installing the inator nozzles
- insert the inator nozzle P into the air outlet A of the
vacuum, and connect the other end into the air inlet of
an inatable object. ea
- insert the small inator nozzle N into the inator nozzle
P and the tip into the air inlet of an inatable object. eb
MAINTENANCE / SERVICE
• Always keep tool clean (especially air outlet A 2)
! remove battery from tool before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
• Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
Only for EU countries
• Do not dispose of electric tools, accessories and
packaging together with household waste material
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
Only for UK
• Do not dispose of electric tools, accessories and
packaging together with household waste material
- in observance of on Waste Electric and Electronic
- Equipment Regulations 2013 (SI 2013/3113), electric
tools that have reached the end of their life must be
collected separately and returned to an environmentally
compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
b
ASPIRATEUR +
GONFLEUR
3167
with household waste material
USE
• Charging battery
! read the safety warnings and instructions
provided with the charger
• Removing/installing the battery 2
• Battery level indicator 7
- press the battery level indicator button E to show the
current battery level 7a
! when the lowest level of the battery indicator
7b, the
battery is empty
!
after pressing button E 7c, the battery is not
within the allowable operating temperature range
• Battery protection
The tool is suddenly being switched o or prevented from
being switched on, when
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
levels of the battery level indicator start ashing when
pressing button E 7c; wait until battery has returned
within the allowable operating temperature range
- the battery is nearly empty (to protect against
deep discharge) --> a low battery level or ashing low
battery level 7b is shown by the battery level indicator
when pressing button E; charge battery
!
damaged
• On/o
- switch on/o the tool by press switch H 2
- when the switch H 2 is pressed for rst time, the
vacuum will operate at high speed.
- Press the on/o switch H 2 again, to turn o the
vacuum.
• Mode selection
- press the mode button G 2 to switch the vacuum
between high speed and low speed modes.
• Mounting/removing accessories 8
- connect nozzle K or L to the end of vacuum hose F
- for removing accessories vice-versa
• Empty dust compartment 9
! remove battery from tool before cleaning
- press release button D to open the dust compartment
cover.
- empty dust compartment J
- clean lter assembly if necessary (see below)
- press the dust compartment cover into place
! never operate the tool without the necessary
! optimal dust pick-up performance will only be
compartment
• Cleaning of lter assembly q
- remove the lter assembly from the dust compartment
- remove the lter cover Q from the fabric lter R.
- brush the lter cover Q with a soft brush. If necessary,
you can wet clean the lter cover Q.
- wash the fabric lter R under running water.
!
when reassembling
Приклучете се во разговорот за овој производ
Тука можете да го споделите вашето мислење за Skil 3167 CA Правосмукалка. Ако имате прашања, најпрво прочитајте го прирачникот. Можете да побарате прирачник ако го употребите нашиот прирачник за контакт.