Прирачник Skil 1005 AM Батериска дупчалка

Прирачник

11

CHARGING/BATTERIES

• This charger can be used by

children aged 8 and above and

by persons who have physical,

sensory or mental limitations

or a lack of experience or

knowledge if a person

responsible for their safety

supervises them or has

instructed them in the safe

operation of the charger and

they understand the

associated dangers (otherwise,

there is a danger of operating

errors and injuries)

• Supervise children (this will

ensure that children do not play

with the charger)



maintenance of the battery

charger shall not be made by

children without supervision

• Only use SKIL charger 2610Z07481 and SKIL battery

pack(s) 2610Z07330 with this tool

• Do not touch the contacts in the charger

• Do not expose tool/charger/battery to rain

• Do not charge battery in damp or wet environments

• Do not use charger when damaged; take it to one of the

ocially registered SKIL Service Stations for a safety

check

• Do not use charger when cord or plug is damaged; cord

or plug should be replaced immediately at one of the

ocially registered SKIL Service Stations

• Do not use battery when damaged; it should be replaced

immediately

• Do not disassemble charger or battery

• Do not attempt to recharge non-rechargeable batteries

with the charger

• Permitted ambient temperature (tool/charger/battery):

- when charging 0...+45°C

- during operation –20...+50°C

- during storage –20...+50°C

EXPLANATION OF SYMBOLS ON TOOL/CHARGER/

BATTERY

3 Read the instruction manual before use

4 Only use the charger indoors

5 Double insulation (no earth wire required)

6 Incorrect polarity of the charger connection could cause

a hazard (only charge the battery with the charger

supplied)

7 Automatic shut-o when charger gets too hot (thermic

fuse blows and charger becomes useless)

8 Do not dispose of electric tools and batteries together

with household waste material

USE

• Charging battery 9

- battery of new tools is not fully charged

- connect charger to power source as illustrated

- insert battery into charger

- red light B will turn on indicating that the battery is

being charged

- red light B will stay on as long as the battery is

connected to the charger and the charger is in the wall

socket

! remove battery from charger after charging

period has ended thereby lengthening the service

life of the battery

IMPORTANT:

- after 8 hours the charging operation will be completed,

and the battery may be used

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- ensure that the outside surface of the battery is clean

and dry before inserting into charger

- do not charge at temperatures below 0°C and over

45°C; this will seriously damage the battery as well as

the charger

- do not remove battery from tool while it is running

! a battery that is new or has not been used for a

longer period does not develop its full capacity

until after approximately 5 charging/discharging

cycles

- do not repeatedly recharge the battery after only a few

minutes of operation; this may result in a reduction of

operating time and battery eciency

- if you anticipate long periods of non-use for the tool, it

is best to unplug the charger from its power source

• On/O 0

• Speed control for smooth starting !

• Changing direction of rotation @

- when not properly set in left/right position, switch C 2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits #

- insert the bit as deep as possible in the chuck

! do not use bits with a damaged shank

• Torque control (VariTorque) $

- output torque will increase as clutch ring F is rotated

from 1 to 20; position G will lock up the clutch to permit

drilling or driving heavy duty work

- when turning in a screw, rst try VariTorque position 1

and increase until the desired depth has been reached

• Mechanical gear selection %

- set selector H to desired speed

! actuate the gear selector while tool is running

slowly

1 = LOW SPEED

- high torque

- for screwdriving and drilling large diameters

- for tapping thread

2 = HIGH SPEED

- lower torque

- for drilling small diameters

Оцена

Повеќе за овој прирачник

Разбираме дека е практично да имате печатен прирачник за Skil 1005 AM Батериска дупчалка. Секогаш можете да го преземете прирачникот од нашата интернет-страница и да го отпечатите сами. Ако сакате да го имате оригиналниот прирачник, ви препорачуваме да контактирате со Skil. Тие можеби ќе можат да ви дадат оригинален прирачник. Барате прирачник за вашите Skil 1005 AM Батериска дупчалка на различен јазик? Изберете го претпочитаниот јазик на нашата интернет-страница и пребарајте го бројот на модел за да видите дали го имаме.

Спецификации

Сите прирачници за Skil Батериски дупчалки
Повеќе прирачници за Батериски дупчалки

Поврзани производи

Прирачник

Skil 3020 HA Батериска дупчалка

Прирачник

Skil 3066 JA Батериска дупчалка

Прирачник

Skil 3020 HC Батериска дупчалка

Прирачник

Skil 3060 AA Батериска дупчалка

Прирачник

Skil 3008 HF Батериска дупчалка

Прирачник

Skil 0931 AA Батериска дупчалка

Прирачник

Skil 3008 HE Батериска дупчалка

Прирачник

Skil 3020 AA Батериска дупчалка

Поврзани категории