Прирачник Skil 0740 AA Тример за жива ограда

Прирачник

7

USE

• Cord restraint 8

- hook the loop in the extension cord over restraint A as

illustrated

- pull tight to secure the extension cord

• Two-hand safety switch 9

Prevents the tool from being switched on accidentally

- switch on the tool by pressing both switch B and

switch C

- switch o the tool by releasing either switch B or

switch C

• Operating the tool

! starttrimmingonlywhenmotorisrunning

! donotcutgroundcoveringplantsinorderto

preventearth/sandfromdamagingcuttingbladesD

! donotoverloadthetoolbycuttingstemslarger

than14mminthickness

- move tool away from cutting area before switching o

! afterswitchingoffthetoolthebladescontinueto

moveforafewseconds

• Blade tip protector F 2

- prevents kickback of the tool when solid objects (such

as fence posts or house walls) are touched

- protects the end blades from damage

• Trimming hedges 0

- trim the sides of the hedge rst (from the bottom

upwards), then cut the top

- trim the side of a hedge in such a way that it will be

slightly narrower at the top

- use a hand saw or pruning shears to cut thicker

branches

• Holding and guiding the tool

- hold the tool rmly with both hands and take a secure

stance

! whileworking,alwaysholdthetoolatthe

grey-colouredgriparea(s)!

- guide the tool ahead of you

- always ensure that the extension cord is guided away

from the work area

- start trimming near the mains socket and move away

while working

APPLICATIONADVICE

• For trimming a hedge at a uniform height level

- fasten a piece of string along the length of the hedge

at the desired height

- trim the hedge just above this string

• Recommended cutting/trimming times (Western Europe)

- trim hedges with deciduous leaves in June and

October

- trim evergreen hedges in April and August

- trim conifers and other fast-growing shrubs every 6

weeks from May until October

MAINTENANCE/SERVICE

• This tool is not intended for professional use

• Keep tool, cord and cutting blades clean

! disconnecttheplugbeforecleaning

- clean the tool with a damp cloth (do not use cleaning

agents or solvents)

- clean ventilation slots G 2 regularly with a brush or

compressed air

- after use, always carefully clean and lightly lubricate

the cutting blades

! weargloveswhenhandlingorcleaningthe

cuttingblades

• Regularly check the condition of the cutting blades and

the tightness of the blade bolts

• Regularly check for worn or damaged components and

have them repaired/replaced when necessary

• Sharpening the cutting blades

! disconnecttheplugbeforesharpening

- sharpen the cutting blades with a small and smooth

le, in case a solid object damaged them

- we advise you, however, to have the blades sharpened

by a specialist

- lubricate the cutting blades after sharpening

• Storage @

- securely mount storage rail H on the wall with 4 screws

(notsupplied) and horizontally leveled

- use blade cover J when storing the tool

- before storing the tool, wipe o the cutting blades with

an oil-soaked rag to prevent corrosion

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skil.com)

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

! switchoffthetoolanddisconnecttheplugbefore

investigatingtheproblem

★ Motor does not start or stops suddenly

- power supply socket faulty -> use another socket

- plug not connected -> connect plug

- extension cord damaged -> replace extension cord

★ Tool operates intermittently

- extension cord damaged -> replace extension cord

- internal wiring defective -> contact dealer/service

station

- on/o switch defective -> contact dealer/service

station

★ Motor runs but blades remain stationary

- internal fault -> contact dealer/service station

★ Cutting blades hot

- cutting blades blunt -> have blades sharpened

- cutting blades have dents -> have blades inspected

- too much friction due to lack of lubricant -> lubricate

blades

Оцена

Повеќе за овој прирачник

Разбираме дека е практично да имате печатен прирачник за Skil 0740 AA Тример за жива ограда. Секогаш можете да го преземете прирачникот од нашата интернет-страница и да го отпечатите сами. Ако сакате да го имате оригиналниот прирачник, ви препорачуваме да контактирате со Skil. Тие можеби ќе можат да ви дадат оригинален прирачник. Барате прирачник за вашите Skil 0740 AA Тример за жива ограда на различен јазик? Изберете го претпочитаниот јазик на нашата интернет-страница и пребарајте го бројот на модел за да видите дали го имаме.

Спецификации

Сите прирачници за Skil Тримери за жива ограда
Повеќе прирачници за Тримери за жива ограда

Поврзани производи

Прирачник

Skil 0429 AA Тример за жива ограда

Прирачник

Skil 0755 AA Тример за жива ограда

Прирачник

Skil 0640 CA Тример за жива ограда

Прирачник

Skil 0745 AA Тример за жива ограда

Прирачник

Skil 0750 AA Тример за жива ограда

Прирачник

Skil 0429 CA Тример за жива ограда

Прирачник

Skil 0428 AA Тример за жива ограда

Прирачник

Skil 0480 CA Тример за жива ограда

Поврзани категории