Прирачник Adler AD 1357 Автомат за вода

Прирачник

6

NOTE!

The first 2 tanks of filtered water may contain residues of activated carbon - not suitable for drinking. Water from the first two cycles

should be poured out.

After that, the water will be clean and ready for consumption.

The buttons on the touch panel (4) should be touched only with fingertips, touching with fingernails may damage the panel !

METHOD OF USE

Open the water tank cover (3) and fill the tank (2) with clean water (not exceeding the MAX level). Plug the power cord plug into a

220-240V ~50/60Hz grounded power outlet. Place the cup on the drip tray (6) under the spout/ faucet (5). Press the LOCK button

for 2-3 seconds to unlock the panel. Select the desired temperature by pressing the TEMP button (2). Select the desired amount of

water by pressing the VOLUME button (3). Press the START/STOP button (4), water will start flowing out of the spout (5). The

machine will automatically stop pouring when the selected amount is reached.

NOTE!

Do not touch the boiling water and steam to prevent burns.

If only a small amount of water is poured, the desired temperature may vary. The difference may be + - 15%.

If the device has not been used for a long time, deposits may form. In this case, make 100 ml of water at 100 ° C to rinse the

device.

The amount of set water may vary by + - 15%.

The device remembers the last setting before it is unplugged.

MANUAL RESETTING OF THE THERMOSTAT

The unit is equipped with a reset thermostat to restore the heating function

in case of unexpected tripping. If the manual thermostat shuts down, remove the reset key (12) located under the base of the unit,

then insert it into the thermostat reset hole (10).

REMOVING WATER FROM THE DRIP TRAY

When the drip tray (6) is full, grasp and stabilize the appliance with one hand, and with the other hand lift the tray slightly to remove

it, empty the tray and put it back into its original place using enough force.

FILTER CHANGE

When F1 (7) appears on the display, it means that the filter needs to be replaced (after about 150 l). Open the tank lid (3) and

remove the entire filter basket (7 and 8). Remove the used cartridge and install the new one according to the preparation and

installation steps. After replacement, press the TEMP and VOLUME buttons (2 and 3) simultaneously for about 3 seconds. The unit

will beep and the F1 message (7) will disappear. The filter operation counter will be reset.

CLEANING AND MAINTENANCE

Always turn off the water dispenser, unplug it from the power supply and let it cool completely before cleaning. Do not immerse the

device in any liquid to avoid damage. Do not use any chemicals, metal, wood or abrasive detergents to clean the housing of the

device . Always use a damp cloth.

After cleaning the device, open the drain plug (11) to remove dirt. After opening, tighten the plug.

Note: If you find water leaking from underneath, tighten the drain plug (11).

Always handle the device carefully, do not put it close to the edge of the table and countertop , in order to prevent deformation or

damage in case of accidental fall from the table.

Scale deposited inside the appliance should be removed regularly. This activity is not subject to warranty service. Lack of regular

descaling will lead to damage to the device and will void the warranty.

After about 10 hours of operation of the appliance, the descaling light "Descaling" (6) will light up. This is when the cleaning process

should be carried out. Prepare a descaling solution - pour about 80 g of citric acid or pour 100 ml of vinegar into the water tank (2),

and then add water to half the capacity of the tank (2).

Press and hold the VOLUME setting button (3) for 3 seconds to activate the descaling mode. The device will start working and draw

water from the tank until it is empty. Then prepare the same solution again (80 g of acid or 100 ml of vinegar, plus water to half of

the tank). Set the temperature to 45°C and select the amount of 200 ml of water. Then leave the appliance at rest for about 2 hours

so that the descaling agent can take effect. After 2 hours, repeat the first step - that is, start the descaling mode and let the device

empty the tank. Fill the tank to capacity with clean water and once again start the process from step 1. Fill the tank again with clean

water and repeat step 1 to thoroughly rinse out any residual decalcifying agent.

TECHNICAL SPECIFICATIONS:

Оцена

Повеќе за овој прирачник

Разбираме дека е практично да имате печатен прирачник за Adler AD 1357 Автомат за вода. Секогаш можете да го преземете прирачникот од нашата интернет-страница и да го отпечатите сами. Ако сакате да го имате оригиналниот прирачник, ви препорачуваме да контактирате со Adler. Тие можеби ќе можат да ви дадат оригинален прирачник. Барате прирачник за вашите Adler AD 1357 Автомат за вода на различен јазик? Изберете го претпочитаниот јазик на нашата интернет-страница и пребарајте го бројот на модел за да видите дали го имаме.

Спецификации

Сите прирачници за Adler Автомати за вода
Повеќе прирачници за Автомати за вода