Прирачник Adler AD 1356 Автомат за вода

Прирачник

6

Fill the tank with water.

NOTE!

The first 2 tanks of filtered water may contain residues of activated carbon - not suitable for drinking. Water from the first two cycles

should be poured out.

After that, the water will be clean and ready for consumption.

The buttons on the touch panel (4) should be touched only with fingertips, touching with fingernails may damage the panel !

METHOD OF USE

Open the water tank cover (3) and fill the tank (2) with clean water (not exceeding the MAX level). Plug the power cord plug into a

220-240V ~50/60Hz grounded power outlet. Place the cup on the drip tray (6) under the spout/ faucet (5). Press the LOCK button

for 3-5 seconds to unlock the panel.

Select the desired temperature by pressing the TEMP button (2). Select the desired amount of water by pressing the VOLUME

button (3). Press the START/STOP button (5), water will start flowing out of the spout (5). The machine will automatically stop

pouring when the selected amount is reached.

NOTE!

Do not touch the boiling water and steam to prevent burns.

If only a small amount of water is poured, the desired temperature may vary. The difference may be + - 15%.

If the device has not been used for a long time, deposits may form. In this case, make 100 ml of water at 100 ° C to rinse the

device.

The amount of set water may vary by + - 15%

The device remembers the last setting before it is unplugged.

MANUAL RESETTING OF THE THERMOSTAT

The unit is equipped with a reset thermostat to restore the heating function

in case of unexpected tripping. If the manual thermostat shuts down, remove the reset key (12) located under the base of the unit,

then insert it into the thermostat reset hole (10).

REMOVING WATER FROM THE DRIP TRAY

When the drip tray (6) is full, grasp and stabilize the appliance with one hand, and with the other hand slightly lift the tray to remove

it, empty the tray and put it back into its original place using enough force.

FILTER CHANGE

When the message "Change filter" (7) appears on the display, it means that the filter needs to be changed (after about 150 l). Open

the tank lid (3) and remove the entire filter basket (7 and 8). Remove the used cartridge and install the new one according to the

preparation and installation steps. After replacement, press the LOCK and START/STOP buttons (1 and 5) simultaneously for

about 3-5 seconds. , and then the unit will beep 3 times. The message "Change filter" (7) will be turned off and the filter life counter

will be reset.

CLEANING AND MAINTENANCE

Always turn off the water dispenser, unplug it from the power supply and let it cool completely before cleaning. Do not immerse the

device in any liquid to avoid damage. Do not use any chemicals, metal, wood or abrasive detergents to clean the housing of the

device . Always use a damp cloth.

After cleaning the device, open the drain plug (11) to remove dirt. After opening, tighten the plug.

Note: If you find water leaking from underneath, tighten the drain plug (11).

Always handle the device carefully, do not put it close to the edge of the table and countertop , in order to prevent deformation or

damage in case of accidental fall from the table.

Scale deposited inside the appliance should be removed regularly. This activity is not subject to warranty service. Lack of regular

descaling will lead to damage to the device and will void the warranty.

After about 10 hours of operation of the appliance, the descaling light "Descale" (8) will light up. The cleaning process should then

be carried out according to the following steps:

Preparation of the solution:

Pour about 80 g of citric acid or pour 100 ml of vinegar into the water tank. Then add water to half of the tank (2) and mix. Press

and hold the volume setting button "VOLUME" (3) for 3 seconds to start the descaling mode. Let the machine run until the tank (2)

is completely empty. Prepare the solution again (80 g of citric acid or 100 ml of vinegar + water to half of the tank).

Set the temperature to 45°C and the volume to 200 ml. Leave the device for about 2 hours for the solution to work.

After two hours, repeat step 1 - start descaling mode and empty the tank (2). Fill the reservoir with clean water to the full and

perform step 1 (rinse) again. Once again fill the tank (2) with clean water and repeat step 1 to rinse the device thoroughly.

Оцена

Повеќе за овој прирачник

Разбираме дека е практично да имате печатен прирачник за Adler AD 1356 Автомат за вода. Секогаш можете да го преземете прирачникот од нашата интернет-страница и да го отпечатите сами. Ако сакате да го имате оригиналниот прирачник, ви препорачуваме да контактирате со Adler. Тие можеби ќе можат да ви дадат оригинален прирачник. Барате прирачник за вашите Adler AD 1356 Автомат за вода на различен јазик? Изберете го претпочитаниот јазик на нашата интернет-страница и пребарајте го бројот на модел за да видите дали го имаме.

Спецификации

Сите прирачници за Adler Автомати за вода
Повеќе прирачници за Автомати за вода